Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
We have come across this article involving Tools You Need to Install a New Bathtub listed below on the net and decided it made good sense to talk about it with you on this page.
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the project can move immediately; if you need to open up a wall surface to get rid of the old tub and place the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will require a helper to move out the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the job and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your restroom if you have actually currently purchased a new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your tools as well as material checklist must make up the following:
Getting ready for the Installation
First of all, the sustaining framework provided with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, activate the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, put the bathtub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Activate the water supply as well as inspect all joints and also new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the faucet in place with the maker offered backnut. When the faucet is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealant can break fairly very early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I'm certainly very eager about Installing A Bathtub and I am praying you appreciated the entire post. Are you aware of another person who is occupied with the subject? Why not share it. Thank you so much for your time spent reading it.
24/7 plumbers for emergencies. Report this page